F8 SERIES

F8 Series

This is the latest series to join our range of CNC fins. It is loosely based on the DV9 design but with the added tip extension. Most of the designs in this series feature a slight flip in the tip as well, called the FLIPTWO.

This new design is a high-performance fin that handles various conditions. It features our PHAT FOILS and HOLOFOILS, with the FLIPTWO allowing for more efficient HOLOFOILS. In addition, extending the tip gives the fin a lot more feel later into the turn while also providing a better pivot point.

The main body of the fin is more wing-like than the typical fin and allows the fin to be very efficient at generating lift and thereby creating forward momentum.

Due to how the FLIPTWO is implemented, the fin profile features a distinctive taper from the base to the transition to the flip. The FLIPTWO is, in turn, a lot thinner than our first-generation flips. We are minimizing the risks of cavitation. There is also a slight hollowing of the inside face of the flip to give it a little more bite during a turn.

A dedicated center fin design features even more prominent tips to provide greater holding power and feel in the water. In addition, the center fin has very distinctive foils that differentiate between the throat and blade of the fin.

F8 Series Details

NEW
F8-425FT TWIN CNC

Currently, the smallest fin in this series. Intended for use as the back fin in a QUAD setup or the front fin in a TWINZER or REVERSE QUAD setup. It is also an ideal side bite for a 2PLUS1 setup. Like its larger sibling, it features the FLIPTWO flipped tips.

DIMENSIONS

height: 4.25" [108mm]
base: 2.875" [73mm]
area: 9.28 in2 [59.87 cm2]

MSRP: US$80.00

Price includes fin bag and key

Set of two fins

SKU: CNC-F8-425FT-TWIN

PURCHASE
NEW
F8 Series
F8-500FT TWIN CNC

This is the main side fin, used as QUAD front fins, THRUSTER side fins combined with the F8-438C center fin. They can also be used as a smaller twin fin. Features the FLIPTWO flipped tips.

DIMENSIONS

height: 5.00" [127mm]
base: 2.875" [73mm]
area: 12.73 in2 [82.13 cm2]

MSRP: US$80.00

Price includes fin bag and key

Set of two fins

SKU: CNC-F8-500FT-TWIN

PURCHASE
NEW
F8 Series
F8-438C TWIN CNC

This series's main center fin, combined with the F8-500FT side fins for a THRUSTER setup. They can also be used with the smaller F8-425FT twin fin in a grom setup.

DIMENSIONS

height: 4.375" [111mm]
base: 2.875" [73mm]
area: 11.41 in2 [74 cm2]

MSRP: US$40.00

Price does not include a fin bag or key

Single fin

SKU: CNC-F8-438C-CENTER

PURCHASE

COMBOS

F8 Fin Combinations

Given this series's initial small range of sizes, we could not create all the possible combinations, but these are the standard ones.

Additional combinations can be created by mixing them with other fins, some of which are also shown here.

Also available from our distributor

CNC Price List

TWIN Set
$80.00
THRUSTER Set
$120.00
QUAD Set
$160.00
5FIN Set
$200.00
CENTER Fin
$40.00

All prices subject to change without notice

WARNING - DUAL TAB Fin Bases

HANALEI FINS cannot guarantee against the breakage of dual tab bases. The DUAL TAB system is designed to break under specific loads or hard impacts.

We try to make the tabs as strong as possible, but there is only so much we can do before we run into the limitations of the base design.

If a DUAL TAB base does break, we will work with the customer to replace the fins at a reduced price, but we cannot outright replace the fins at no charge!

NOTE - REPLACEMENT Fins

HANALEI FINS cannot sell individual side fins should you lose a side fin, as it means we have to break up a set of fins. So we are left with a fin that we have little chance of selling by itself.

If a fin is lost, we will work with the customer by selling a set of replacement fins at a reduced price. These replacement fins would not be in a bag to keep the cost down!

INFO - FLIP TIP Fins

For anyone interested in our fins featuring FLIP TIPS, please be aware that these fins are sensitive to the amount of toe-in used in the box setup, so it is worth checking with us.

We have encountered several cases where fin boxes set up with excessive toe-in have caused issues with fins featuring FLIP TIPS. We want to ensure there are no problems with our fins. Therefore we are offering to verify that they will work in the setup on any given board before buying any of these fins.

Before you order any of these fins, if you are unsure whether they will work on your board, please CONTACT us so we can ensure they will work for you!

OFFICES

Primary office locations for HANALEI FINS - Australia and Hawai'i (USA). Contact info is provided here, but the preferred contact method is through the contact form on this site.

+61 2 4339 9580

+1 808 639 5303